TECH-SONIC™
Insert Type TEC series & Stud Type TCTS series
Features a unique combination of opposed knurls and knurled vanes providing increased performance levels, even over the Sonic-Lok insert. Installation is simplified by the symmetrical nature of theinsert, eliminating the need for orientation during automated or hand feeding.
Click here to view pdf
|
 |
SONIC-LOK™
Insert Type SL & SHK series and Stud Type SLTS & SLHS series
Has been designed for rapid installation into thermoplastics using heat or ultrasonic. It features opposed helical knurl bands to provide a combination of high torque and pull out resistance.
Click here to view pdf
|
 |
TAPER-X™
Insert Type TX series
Has been designed for those instances where fasteners must be installed into a 8° tapered hole. The combination of angled splines and upwardly directed vanes provide high torque and pull-out performance.
Click here to view pdf
|
 |
6030 INSERT
Insert Type 6030 & 6030H series
Has been developed for installation into thermoplastics where the design incorporates a tapered hole configuration. The parallel body design combined with the opposing helical knurl bands enables users to achieve up to a 25% increase in productivity by the ability to reduce the recommended dwell time compared with standard tapered hole inserts.
Click here to view pdf
|
 |
HI-TORK™
Insert Type HT series
Offering high pull out/torque performance. Hi-Tork is recommended for high fill plastics with reduced installation depth, is tolerant of moulding process variables and provides high process capability.
Click here to view pdf
|
 |
MINI-TECH™
Minsert Type TEC series & Stud Type TCTS series
A miniature insert with all the design features and characteristics of the Tech-Sonic range. It is ideal for today’s smaller plastic products and enables the use of very small screws that will provide complete re-usability with no risk of thread stripping problems.
Click here to view pdf
|
 |
HEAT-LOK™
Insert Type HL & HLH and Stud Type HLTS & HLHS series
Designed for installation into notch sensitive amorphous thermoplastics by heat. It features rounded knurls, avoiding the stress raising sharp crests and roots which typify knurls used on most inserts.
Click here to view pdf
|
 |
PRESS-LOK™
Insert Type PLK series
Offers ease of installation without the typical high screw installation torque and its plain and knurled vanes offer the levels of pull-out and torque resistance usually expected only of heat-installed inserts.
Click here to view pdf
|
 |
SPIRO™
Insert Type SP & HSR series and Stud Type SPTS & SPHS series
Designed to cope with the difficulties presented by hard brittle thermoset materials. The sharp precision knurl pattern cuts into these materials reducing radial stresses and allowing thinner boss walls than many other inserts.
Click here to view pdf
|
 |
BANC-LOK™
Insert Type N41, N42 & N42R series
Ideal for use in hard thermosetting plastics, BancLok are press-in expansion inserts which, due to their diamond knurl pattern, give minimum penetration of the sides of the hole without sacrificing pull-out resistance.
Click here to view pdf
|
 |
FIN-LOK™
Insert Type FL & FLH and Stud Type HLTS & HLHS series
A press-in insert, which can be easily installed into most thermoplastic materials. It features a combination of sharp fins and straight knurls. Unlike the Press-Lok range, this insert has a free running thread.
Click here to view pdf
|
 |
SCREW-SERT™
Insert Type SCT & HSCT series & Stud Type SCTS series
A self-tapping insert suitable for installation into a wide range of thermoplastic and thermosetting plastic materials. They are particularly suitable for applications involving high jack-out loading and materials with low core strengths.
Click here to view pdf
|
 |
FLO-TECH™
Insert Type FTC series
A blind-ended threaded insert which has been introduced to meet the needs of those moulders who, for a variety of reasons, prefer to mould-in. The unique design of three opposed helical knurl bands combined with the included recesses give extremely high levels of performance in both pullout and torque tests.
Click here to view pdf
|
 |
|
Technical details may change. Please contact HWE for latest drawings and specifications. Alternatively you can fill out our
Online Quotation Form
. Order conditions and minimum quantities may apply for some products.
|
|
